固溶处理对TiB2/6061复合材料硬度及耐磨性的影响

采用氟盐法制备了TiB₂质量分数为3%的原位合成TiB₂/6061复合材料,研究了固溶温度和固溶时间对复合材料硬度和耐磨性能的影响。结果表明:TiB₂颗粒弥散分布在6061铝合金基体中,明显细化6061铝合金基体晶粒。当固溶温度一定时,随固溶时间延长,复合材料的硬度和耐磨性可获得明显提高,但固溶时间在6~10 h时,复合材料的性能变化不显著。当固溶时间一定时,随固溶温度升高,复合材料硬度和耐磨性呈现先上升后下降的趋势。3wt%TiB₂/6061复合材料经530 ℃×10 h固溶处理后,硬度和耐磨性能最佳,相较于铸态硬度值提高了79.5％,磨损量减少了59.1%。固溶处理后复合材料的磨损表面犁沟变细变浅,材料脱落现象减少。     

Production of Synthesis Gas via Dry Reforming of Methane over Co‐Based Catalysts: Effect on H2/CO Ratio and Carbon Deposition

The effect of support type on synthesis gas production using Co‐based catalysts supported over TiO₂‐P25, Al₂O₃, SiO₂, and CeO₂ was investigated. The catalysts were prepared by the incipient wet impregnation method and characterized by various techniques for comparison. Experiments were performed in a micro tubular reactor. The results revealed that all Co‐supported catalysts produced synthesis gas ratios of 1 and below and, thus, proved to be well‐suited for methanol and Fischer‐Tropsch syntheses. Co catalysts supported over TiO₂‐P25 and Al₂O₃ provided better synthesis gas ratios and stability performances. The promotion of a Co/TiO₂‐P25 catalyst with Ce had a substantial influence on its catalytic activity and the amount of carbon deposit. A Ce‐promoted catalyst diminished markedly the extent of carbon deposition and thus boosted the performance towards better activity and stability.     

Isolation of the effect of the hairy layer length on the mechanical properties of waterborne coatings

The effect of the acidic hairy layer length on the interdiffusion of polymer between particles and as a consequence on the mechanical properties of the films produced from waterborne coatings has been studied. In order to isolate this effect, latexes with the same particle diameter and molecular weight but stabilized with poly(acrylic acid)-block-poly(butyl acrylate) (PAA-b-PBA) block copolymers of controlled and different lengths were prepared. Tensile strength measurements showed at the macroscopic level that the presence of AA chains in the particle surface reduced the mechanical properties of the films dried at room temperature, being its effect worse the longer the AA chain length. Higher annealing temperatures erased the negative effect of the acidic hairy layer on mechanical properties. The neutralization with NaOH instead of with NH₄OH also led to worse mechanical properties. These macroscopic results were supported by Fluorescence Resonance Energy Transfer (FRET) experiments that showed that at the microscopic level, the extent of interdiffusion occurred slower when the AA chains in the particles surface increased, the annealing temperature was lower and when NaOH was used as neutralizing agent instead of NH₄OH.     

Linear friction welding of Ti6Al4V: experiments and modelling

Linear friction welding of the Ti6Al4V alloy is studied. A new definition of the energy input rate is proposed, based on an integration over time of the in-plane force and velocity; a strong correlation with the upset rate is then found. The effective friction coefficient is estimated to be 0·5±0·1 for varying frequencies and amplitudes, with only a weak dependence on the processing conditions displayed. A model is proposed that accounts for both the conditioning and equilibrium stages of the process, which is shown to be in good agreement with the experimental data. The model is used to study the mechanism by which the flash is formed. A criterion is proposed by which the rippled nature of its morphology can be predicted.     

Different chemical effect of hydrogen addition on soot formation in laminar coflow methane and ethylene diffusion flames

Previous studies showed that adding hydrogen (H₂) can have an opposite chemical effect on soot formation: its chemical effect enhances and suppresses soot formation in methane (CH₄) and ethylene (C₂H₄) diffusion flames, respectively. Such opposite chemical effect of H₂ (CE-H₂) remains unresolved. The different CE-H₂ is studied numerically in the two laminar coflow diffusion flames. A detailed chemical mechanism with the addition of a chemically inert virtual species FH₂ is used to model the gas-phase combustion chemistry in this study. Particularly, a reaction pathway analysis was performed based on the numerical results to gain insights into how H₂ addition to fuel affects the pathways leading to the formation of benzene (A₁) in CH₄ and C₂H₄ flames. The numerical results show that the CE-H₂ in CH₄ diffusion flame to prompt soot formation is ascribed that the higher mole fraction of H atom promotes the formation of A₁ and Acetylene (C₂H₂) and leads to higher nucleation rate and eventually higher soot surface growth rate. In contrast, adding H₂ to C₂H₄ diffusion flames decreases soot nucleation and surface growth rate. The lower soot nucleation rate is due to the lower mole fractions of pyrene (A₄), while the lower soot surface growth rate is due to the lower mole fractions of H atom and C₂H₂, higher mole fraction of H₂ and lower soot nucleation rate. Furthermore, the CE-H₂ in C₂H₄ diffusion flames promotes the formation of A₁, but suppresses the formation of A₄.     

含煤盆地深层“超饱和”煤层气形成条件

中国深层煤层气资源丰富，但总体勘探和认识程度较低，尚未形成较为系统的深层煤层气地质理论。通过解剖分析准噶尔盆地白家海凸起和鄂尔多斯盆地临兴区块深层"超饱和"煤层气井的试气/生产动态，估算原地游离气的含气量，分析了深层"超饱和"煤层气的形成条件。研究表明：①深层"超饱和"煤层气储层中除吸附气外，还含有原地游离气，用常规试气方法可直接获得气流，煤层气的产出不明显依赖于排水降压；②埋藏超过一定深度，在煤阶和温度的综合作用下，煤的吸附能力将随埋深的继续增加而降低，煤层中吸附气的饱和度有增加的趋势，在达到吸附饱和后，出现原地游离气并形成"超饱和"煤层气，盆地深层具有"超饱和"煤层气形成的优势条件；③由于地温梯度和压力梯度的不同，不同盆地"超饱和"煤层气出现的临界深度不同，异常高压和异常高热流可以降低深层"超饱和"煤层气形成的临界深度；④深层"超饱和"煤层气开发具有大大缩短见气时间、充分利用地层能量和累积产水量低等优势，有望成为未来煤层气勘探开发的一个重要领域。     

Formation and wear mechanism of nickel titanium intermetallics during heat treatment of nickel coating on Ti-6Al-4V substrate

In the present work, inter-diffusion of nickel and titanium and formation of Ni-Ti intermetallic compounds on Ti-6Al-4V substrate have been studied. Initially, nickel was electrodeposited on the alloy using a modified Watts bath solution at a current density of 2 A dm^?2 for 1?h. The coated specimens were then heat treated for different durations at 750, 800 and 850 °C under argon atmosphere. The effects of temperature and time on the characteristics, hardness and wear resistance of intermetallic phases were investigated. The results showed that a multilayer structure was formed after heat treatment, an outer layer of residual nickel, an area of intermetallic layers with different compositions followed by a solid solution of Ni-Ti. It was also observed that an increase in time or temperature at first led to the formation of thicker intermetallic layers; however, after passing a critical point, the intermetallic layers seem to dissolve into the substrate. Furthermore, the wear rates of the diffusion treated samples were four times lower compared to Ti-6Al-4V alloy when sliding against AISI 52100 hardened steel.     

Distributed adaptive neural networks leader-following formation control for quadrotors with directed switching topologies

The leader-following formation problem is discussed for a team of quadrotors under directed switching topologies. To obtain a more general dynamic model, we describe the quadrotor system in a non-affine pure-feedback form with mismatched unknown nonlinearities. By employing an adaptive neural networks state observer to approximate the unknown nonlinear functions and to reconstruct the immeasurable inner states, we propose a novel distributed output feedback formation control protocol with the backstepping method combining with the dynamic surface control technique. From the Lyapunov stability theorem, all signals in the closed-loop formation system are proven to be cooperatively semiglobally uniformly ultimately bounded for any given bounded initial conditions. Finally, we proved that we verify the performance of the proposed formation control approach by a simulation study.     

靶面激光光斑尺寸原位测量的研究

提供了一种简便易行的靶面激光光斑尺寸原位测量的方法。从高斯光束的横向光强分布特性出发,建立了激光烧蚀斑半径与辐照激光能量、光斑尺寸、烧蚀阈值间的关系式,模拟分析发现辐照激光光斑尺寸对烧蚀斑半径随辐照能量变化曲线有较大影响。对于脉宽为2 ms,波长为1064 nm的激光,实验测量了不同能量激光辐照下相纸烧蚀斑半径,并用推导出的关系式拟合测量数据,获得了靶面处光斑尺寸和样品烧蚀阈值。同时,也测量了不同位置处的光斑尺寸和样品烧蚀阈值,对高斯光束束腰位置和样品烧蚀阈值的光斑尺寸效应进行了验证。研究结果表明该技术结果可靠,简单高效。该技术可以为高能激光与固体物质相互作用的基础研究和激光加工等应用领域中实现简单方便地测量靶面光斑尺寸提供帮助。